303british.com

Home
6x45mm - new!
How are Rimfire Jacketed Bullets Made?
Why I Make Them
Cartridge Specs & Chronology
Cartridge Headstamps
The Accurate Lee Enfield
Shooting & Reloading the 303 British & 303 Epps
Musketry Regulations - WWI
Small Arms Training - WWII
Shooting 7.62x51mm Military Brass: Target Loads
Reloader's Notes: The 7.62x39mm
Load Data
303s on the Net: The Last 14 Years
Lithgow Wood
Reloading & Firearms Articles
AIA Rifles: The Conclusion
The Stevens 200
What About These Stevens Rifles?
Stevens 200 Aftermarket Triggers
A 7.62x39 Bolt Action
Rimfires I Like
The 308 Winchester H&R Survivor Rifle
Paco's Acu'rzr - for 22LR ammunition
Ontario Gun Shops
About Steve
Contact Me

Saving a Burnt Out Jungle Carbine

copyright 2000 - Stephen Redgwell
This type of project is a splendid idea if you come across, or are possession of, a rifle that is not original and cannot be restored. There's a bit of money in this, but as you will see, the results are worth it.

Unlike 90% of home sporterised rifles, this job was done well. It is a tribute to the gunsmiths and the rifle's owner, Mike Travis. He was smart enough to realise that if a proper job was going to be done, he'd need to enlist the pros.

Mike was nice enough to send me these pix and let me use them on the site. My congratulations to him and Ashley Outdoors (now XS Sights - www.xssights.com)

jcmuzzle.JPG
Note the muzzle crown & Ashley sight

Hi Steve,

Well, here are the pictures, finally!

The basic action is a #5 Mk 1. When I found it in a gun store, it had been highly polished and blued, the rear sight was missing, the flash suppressor had been cut off and it was shot out.

The bore was dark! It already had the Ramline synthetic stock installed, and it had a B Square scope mount and a cheap Chinese scope.

I ordered a new barrel from Springfield Sporters. They only had 2 groove barrels ($20), so that's what I ended up with. I also ordered a new, milled rear sight.

I sent the whole thing down to Ashley Outdoors in Texas and their gunsmith, Bo Wallace, did the work. He cut the new barrel to 19" and gave it a target crown.

He also installed the new barrel and one of Ashley's proprietary scope scope mounts. It is basically an aluminum ring that fits over the root of the barrel, and is affixed with Acraglass. The scope rail then extends over the barrel without actually touching it (except at the mounting point). Bo also installed a new Ashley front sight.

jc2.JPG
The scope mount can be seen here without the scope installed

When I got it back, I installed a Leupold Scout Scope using Warne Maxima Steel QD rings. I also installed a Galco 3 point "Ching" sling and a Galco 5 rd butt cuff.

After sighting it in, some of my 1st groups at 100 yds were .75" using Greek surplus ammo! This was repeated multiple times. The barrel seemed to be leading with an extreme amount of copper fouling, so I fire lapped it with a Wheeler firelapping kit. That took care of the problem.
The trigger is still a bit heavy, but now that it's hunting season is over I intend to have it fixed.

It's a better shooter than I am. With Remington 180 gr. RNSPs, it hovers around 1 to 1 1/4" at 100 yards. With Federal 180 gr. SP ammo, it shoots about .75" to 1" at 100 yards. I am still in the process of developing good handloads, but so far it looks very promising.

The whole package, unloaded, weighs about 8 lb - maybe a little more. The OAL is 38.5" It holds its zero when the scope is removed and replaced.

The new Ashley front sight works great with the standard rear sight. Hits on the 200 & 300 yd gongs are a piece of cake with either the scope or iron sights.

Muzzle blast can be a bit fierce, but recoil is no problem at all with the Pachmyr Decelerator recoil pad.

Regards,
Michael Travis

jc1.JPG